Sale and installation of geomembrane sheet

Sale and installation of geomembrane sheets in soil and non-soil pools.
In some areas, after excavating, we will come across layers of sand and granular soil, which causes the inner bed of the excavated pool to be rocky and granular. This is why your agricultural pool or water storage needs leveling and leveling operations as well as removing the stone layer in contact with the geomembrane sheet.

Soft soil should not be used to solve the problem of pebbles and grains, and the idea that pouring layers of soft soil will not cause problems in the walls is incorrect and unprincipled. During the period when the pool is drained, the water pressure is applied to the walls and floor, and over time, this pressure on the soil surface settles and the rocks underneath rise up and damage the geomembrane sheet.

The best solution in these cases is to implement flower straw on the inner surface of the pool or to use felt-like layers of geotextile, which will level and strengthen the soil and increase the life of the pool sheet.

Sale and installation of geomembrane sheet in agricultural pool

In earthen pools, after excavation and leveling of the floor and walls, it is time to apply geomembrane sheets.
To implement the sheet on the soil surface, the pool must be inclined and the slope should be enough so that the sheet is not involved with the lateral pressure of the soil from the side of the pool so that it does not suffer soil fall and damage during the period of using the pool.

After the geomembrane sheets are transferred to the project site and the geotextile layers are installed, they enter the installation phase. The wind speed, ambient temperature and atmospheric conditions of the project have an effect on the installation and safety of the welds, and for example, if the wind is in such a way that the welding machine will connect the layers to each other, the wind will not hinder the work and will not disrupt the work of the machine. .

Also, the air temperature in the project environment is effective for adjusting the welding temperature of the machine, because if the layered welding of the sheets is not done correctly, the possibility of causing problems at the welds will increase during the period of use. The whole project and the pool are underutilized and actually result in financial losses.

In most cases, especially for low-sized pools, geomembrane sheets are cut outside the project and on the flat surface next to the pool, and then removed as connected layers and placed inside the pool.

Usually, sheet cuts are done for the peripheral parts of the pool, so to speak, in the four corners. To do this, the geomembrane sheets are cut into triangular layers to be placed in the corners and installed. The device by which sheet welding is done is called polyethylene sheet welding machine (heat gun Arian Khak Iranian) with high automation, the polyethylene edges of geomembrane sheets are welded and uniform.

Sale and installation of geomembrane sheet with heat gun of Arian Khak Iranian

The function of these roller wedge devices is that it is placed on the welding roller from both edges of the sheets and produces heat up to 450 degrees Celsius with a width of about 80 to 160 mm.

This device moves automatically and performs the welding operation, and the installation operator, with the help of a special wooden ladder, simultaneously controls the movement of the welding machine, cleans the work surface with a cloth so that the sheet welding operation is performed in the best possible way between the geomembrane layers. .

Not being clean on the surface of the sheet causes disruption in the welding system and may also damage the machine and delay the end of the work.

The welding machine is adjusted according to the ambient temperature, humidity level, wind intensity and other environmental issues. The required welding temperature and the speed of movement of the machine are among the things that are adjusted to maximize the performance of the system.

Sale and installation of geomembrane sheet with Arian Khak Iranian team

The installation of geotextile layers is done quickly and with the special device of the Arian Weld thermal dryer, which has a hair dryer-like function and connects the layers by heating the geotextile layers.

Geotextiles are produced and sold with different widths, these layers are opened from the edge of the pool and overlap with a distance of a few centimeters, and are installed on top of each other with a special geotextile iron, and finally the pool is completely covered with a geotextile layer. .
In some areas, the need to implement geotextile is almost mandatory, because the presence of pebbles and roughness in the internal surfaces causes the destruction of the geomembrane sheet and, in the first place, cracking due to the pressure of the stones in the sheet and finally leads to the tearing of the geomembrane sheet.

The geotextile installation tool is a type of industrial hair dryer that produces hot air like other household and cosmetic hair dryers, but with the difference that the temperature of industrial hot air produced and the resulting wind pressure are tens of times higher than normal hair dryers, and the temperature is about 50 It can produce 700 degrees Celsius.

This tool has many uses, which are packaging, drying and decoloring industries. The extremely important advantage of this tool is the non-flame production, because the flames may damage the work surface and cause burns.

Sale and installation of geomembrane sheet and how to order

The price of the geomembrane sheet is based on the square meter. The price of each square meter of this 1 mm thick sheet depends on the quantity and size you need, which you order from the factory, and the factory determines the dimensions for you. Because sheets with this diameter are not very useful.

The most widely used and used type of this insulation is 5.1 mm in diameter; Again, its price depends on the type and variety of materials that are used to create the sheet, and the quality and strength that is produced.

They are not always the same.

Please pay attention to this point:
One of the main reasons for the price of geomembrane sheets not being the same is the rise and fall of the price of polyethylene materials that are used in its formation and creation.

The price of these sheets with a diameter of 2 mm, which have special and unique applications and are usually used in pools with a depth of more than 15 meters, is customized and updated.